In-situ and Layer-by-layer Grain Size Estimation of Additively Manufactured Metal Components using Femtosecond Laser Ultrasonic Technique (Submitted)

Admin

댓글 0조회 수 1164추천 수 0

단축키

←이전 문서

→다음 문서

가 + - Up Down Comment Print

단축키

←이전 문서

→다음 문서

가 + - Up Down Comment Print

Journal: Journal of Manufacturing Processes (SCIE, IF:8.6, JCR: 1%)

Authors: Seong-Hyun Park, Kiyoon Yi, Peipei Liu, Gwanghyo Choi, Kyung-Young Jhang, and Hoon Sohn^*

« Prev Comparisons of second- and third-order ultrasonic nonlinearit...

Comparisons of second- and third-order ultrasonic nonlinearit... 2022.11.15by

Microstructural Characterization of Additively Manufactured M... Next »

Microstructural Characterization of Additively Manufactured M... 2022.02.21by

Category

분류	제목	조회 수
International	Full-range stress–strain curve estimation of aluminum alloys using machine learning-aided ultrasound	210
International	Nondestructive Inspection of Directed Energy Deposited Components Using Scanning Acoustic Microscopy with Metalworking Fluids	165
International	Nondestructive Inspection of Cylindrical Components Repaired Via Directed Energy Deposition Using Scanning Acoustic Microscopy with Metal Lubricants	688
International	Plastic properties estimation of aluminum alloys using machine learning of ultrasonic and eddy current data	226
International	Calibration method using a narrowband signal for measurement of the acoustic nonlinearity parameter	144
International	Comparisons of second- and third-order ultrasonic nonlinearity parameters measured using through-transmission and pulse-echo methods	2585
International	In-situ and Layer-by-layer Grain Size Estimation of Additively Manufactured Metal Components using Femtosecond Laser Ultrasonic Technique (Submitted)	1164
International	Microstructural Characterization of Additively Manufactured Metal Components Using Linear and Nonlinear Ultrasonic Techniques	1376
International	Tensile properties evaluation of additively manufactured Ti-6Al-4V/yttria-stabilized zirconia composite using absolute nonlinear-ultrasonic technique (Submitted)	12589
International	Generation and Measurement of Gigahertz Ultrasonic Waves in Additively Manufactured Thin Metal Components using Femtosecond Laser and Application to In-situ Grain size Monitoring (Submitted)	26507
International	Nondestructive evaluation of micro-oxide inclusions in additively manufactured metal parts using nonlinear ultrasonic technique	20281
International	Mechanical properties estimation of additively manufactured metal components using femtosecond laser ultrasonics and laser polishing	29339
International	Experimental Verification of Contact Acoustic Nonlinearity at Rough Contact Interfaces	50351
International	Compensation of a Second Harmonic Wave Included in an Incident Ultrasonic Wave for the Precise Measurement of the Acoustic Nonlinearity Parameter	46128
International	Measurement of Absolute Acoustic Nonlinearity Parameter Using Laser-Ultrasonic Detection	43711
International	Rapid Molecular Diagnostic Sensor Based on Ball-Lensed Optical Fibers	36739
International	Porosity Evaluation of Additively Manufactured Components Using Deep Learning‑based Ultrasonic Nondestructive Testing (Editor's pick)	12259
International	Deep Learning-Based Ultrasonic Testing to Evaluate the Porosity of Additively Manufactured Parts with Rough Surfaces	21754
International	Analysis of the influence of surface roughness on measurement of ultrasonic nonlinearity parameter using contact-type transducer	510798
International	Indirect Method for Measuring Absolute Acoustic Nonlinearity Parameter Using Surface Acoustic Waves with a Fully Non-Contact Laser-Ultrasonic Technique	31926

태그

나눔글꼴 설치 안내

이 PC에는 나눔글꼴이 설치되어 있지 않습니다.

이 사이트를 나눔글꼴로 보기 위해서는
나눔글꼴을 설치해야 합니다.

✔ 설치 취소

SketchBook5,스케치북5

Impacts of Hanyang's Research :: Nondestuctive Evaluation for Future Safety